BUSHINGS | Top |
Description |
Buy |
BUSHING FRONT PUMP BABBIT image #034 Item #44034 | | BUSHING Pump Teflon coated (SONNAX) (performance) image #034 Item #44034T | | BUSHING FRONT PUMP (DURA BOND SOLID COATED) TH350, TH400, TH425, 4L30E, TH180, TH325, ST300, AT540, ALUMINUM POWER GLIDE image #034 Item #DB44034 | | BUSHING PUMP BABBIT (ROLLED METAL) image #034 Item #8005 | | BUSHING (TH400 SUN GEAR SHAFT and STATOR SHAFT) (4L80E OVERDRIVE SUN GEAR 91-UP / SUN GEAR SHAFT NO GROOVES 91-96) (1.122" OD X .490" WIDE) image #037, 040 Item #34037 | | BUSHING CENTER SUPPORT TH400 64-UP , 4L80E 91-96, TH425 67-UP image #044 Item #34044 | | BUSHING FRONT PLANET 400 64-UP 4L80E 91-UP image #053 Item #34053 | | BUSHING OUTPUT NARROW 400 / 4L80 (.410" WIDE) image #062 Item #34062B | | BUSHING OUTPUT WIDE 400 64-74 (.550" WIDE) image #062 Item #34062 | | BUSHING CASE W/LIP (NO WALK-OUT) (SONNAX) TH400 (ALL) 4L80E 91-UP image #064 Item #S34064BA | | BUSHING CASE TH400 64-UP, CAST IRON POWER GLIDE ALL image #064 Item #34064 | | BUSHING EXTENSION HOUSING BRONZE (1.630"OD, .940" Tall) image #066 Item #44066B | | BUSHING EXTENSION HOUSING BABBIT (1.630"OD, .940" Tall) image #066 Item #44066 | | BUSHING EXTENSION HOUSING 1.500" LONG (1.995" O.D.) 400 65-89 image #066 Item #34066 | | BUSHING EXTENSION HOUSING 1.00" LONG (1.995" O.D.) 400 66-89 image #066 Item #34066B | | BUSHING EXTENSION HOUSING 64-70 (1.795" O.D.) 1.240" LONG image #066 Item #34066A | | BUSHING TAIL HOUSING, Transfer Case, (slip yoke type) (2.010" O.D.) NP208, NP231, NP233, NP236, NP241, NP243, NP246, NP261 with 32 SPLINE OUTPUT, some NP263 (with Slip yoke type) image #066 Item #331066 | |
EXCEDY, ALTO, ALLOMATIC FRICTION PLATES | Top |
Description |
Buy |
FRICTION, INTERMEDIATE, EXEDY FDF HI ENERGY GREEN .080" SMOOTH 91-96 4L80E image #104 Item #J34104 | | FRICTION, INTERMEDIATE, ALTO ENERGY GREEN .090" SMOOTH TH400, TH425 1964-UP image #104 Item #A34104 | | FRICTION FORWARD / DIRECT (HIGH ENERGY GROOVED) (.080 image #106 Item #A34106E | | FRICTION, FORWARD DIRECT, EXEDY FDF HIGH ENERGY .080" SMOOTH TH400 / 4L80E 64-UP image #106, 108 Item #J34106 | |
GASKETS, O-RINGS & MISC. ITEMS | Top |
Description |
Buy |
LIP SEAL SPEEDO DRIVE (PACK OF 2) image #078 Item #44078X | | MODULATOR HOSE 350 69-86 PRE-CUT MOLDED ELBOW image #162 Item #44162 | | PAN GASKET CORK / NEO 400 64-UP image #300 Item #34300 | | PAN GASKET FIBER 400 64-UP image #300 Item #34300F | | GASKET (203) TRANSFER CASE to ADAPTER 350 73-86 (7 BOLT HOLES) image #304 Item #301304A | | GASKET TRANSFER CASE 82-98 NP207 NP231 (5 BOLT HOLES) image #304 Item #351304 | | TRANSFER CASE to ADAPTER GASKET ( 6 bolt holes) (208, 241, 242, 246, 261 GM image #304 Item #331304A | | ADAPTER GASKET -NP205 69-86 (3.450" SMALL HOLE) (8 BOLT HOLES) image #304 Item #311304 | | Gasket, NP205, Adapter, Large Hole Type (3.855" ID Large Hole) (8 BOLT HOLES) image #304 Item #311304A | | GASKET EXTENSION HOUSING 400 65-UP image #305 Item #34305 | | GASKET GOVERNOR COVER (FIBER) 400 image #306 Item #34306 | | GASKET REVERSE SERVO COVER 400 64-UP (METAL) image #307 Item #34307 | | WASHER FRONT PUMP BOLT 8 per PACK image #309 Item #44309 | | O-RING FRONT PUMP BOLT 8 per PACK (WHEN OUT USE NO LONGER AVAILABLE) use washers 44309 image #309 Item #34312 | | GASKET FRONT PUMP to CASE 400 64-UP image #310 Item #34310 | | O-RING SEAL FRONT PUMP TH350, TH400 64-UP image #311 Item #44311 | | GASKET VB. PLATE TO CASE (UPPER) 400 87-UP 7 CHECK BALL TYPE image #320 Item #34320A | | GASKET VALVE BODY SPACER PLATE TO CASE (UPPER) 400 65-87 (6 CHECK BALL) image #320 Item #34320 | | VALVE BODY GASKET SET (UPPER and LOWER) (1964 ONLY) image #320, 321 Item #34322 | | GASKET VALVE BODY TO PLATE (LOWER) 400 65-UP (6 OR 7 BALL) image #321 Item #34321A | | GASKET DETENT SOLENOID 65-98 image #328 Item #34328 | | LIP SEAL, Intermediate clutch piston (inner) TH400 4L80E, 64-UP image #332 Item #34332 | | LIP SEAL, Intermediate clutch piston (outer) TH400 4L80E, 64-UP image #333 Item #34333 | | LIP SEAL, (center lip seal) (TH400 64-UP Forward / Direct clutch piston) (4L80E Direct clutch only 91-97) image #334 Item #34334C | | LIP SEAL, Forward / Direct clutch piston (outer) (TH400 64-UP) (4L80E 91-96) ( TH350 FORWARD PISTON, outer 69-UP ) (WHEN OUT OF STOCK USE PAPER RUBBER KIT) image #335 Item #34335 | | LIP SEAL, Forward / Direct clutch piston (inner) (TH400 64-UP) (4L80E 91-96) image #336 Item #34336 | | Seal, Rear Servo Piston (TH400 65-Up) (4L80E 91-UP) image #363 Item #34363 | | O-RING INTAKE TUBE to CASE GM TH400 S300 image #368 Item #12368A | | O-RING SPEEDO HOUSING 400 65-98 image #369 Item #34369A | | O-RING SEAL (VARIOUS USE) SPEEDO .750" OD: O-RING SEAL MODULATOR, CASE CONNECTOR image #369, 368, 346, 347 Item #44369B | | O-RING FILLER TUBE VARIOUS GM/ FORD/ CHRYSLER image #371 Item #44371A | | MULTI LIP SEAL SLEEVE OIL FILLER TUBE image #371 Item #44371B | | O-Ring, Output Shaft to Yoke TH400 65-UP image #374 Item #34374 | | UNIVERSAL GM DUST COVER image #463 Item #M463D | | CUP PLUG EXPANSION 3/8" DIAMETER (FOR PARK PIN and VARIOUS USE) image #483 Item #54483A | | UNIVERSAL FILLER TUBE and STICK (TH350, TH400 image #494 Item #T44494U | | FILLER TUBE REPAIR TIP, ( REPAIR BROKEN OR DAMAGED FILLER TUBE END) image #494 Item #T44494R | | CHECK BALL STEEL .250" VARIOUS valve bodys (each) image #741 Item #44741-5 | | Repair Kit, Fixes 5 Valve Body Plate Holes with 1/4" Check Balls, Fits Most Applications image #747, 741, 740 Item #VB-101 | | BOLT CENTER SUPPORT 400 64-UP image #783 Item #D34783 | | Pan Magnet, Square (.180" Thick, 1.100" x .750") image #839 Item #A44839 | | Pan Magnet, Round (.250" Thick, 1 3/4" OD) image #839 Item #A44839B | | SPEEDO DRIVE GEAR 19 TEETH (USED) (TH400) image #847 Item #U34847-19 | | SPEEDO DRIVE GEAR 18 TEETH (USED) (TH400) | PLASTIC GEAR image #847 Item #U34847-18 | | SPEEDO DRIVEN GEAR 34T-GM (GREEN) image #848A Item #A34848A | | SPEEDO DRIVEN GEAR 35T-GM image #848B Item #A34848B | | SPEEDO DRIVEN GEAR (WHITE) 36T-GM image #848C Item #A34848C | | SPEEDO DRIVEN GEAR 37T-GM image #848D Item #A34848D | | SPEEDO DRIVEN GEAR 38T-GM image #848E Item #A34848E | | SPEEDO DRIVEN GEAR 39T-GM (BROWN) image #848F Item #A34848F | | SPEEDO DRIVEN GEAR 40T-GM image #848G Item #A34848G | | SPEEDO DRIVEN GEAR 41T-GM image #848H Item #A34848H | | SPEEDO DRIVEN GEAR (GREEN) 42T-GM image #848HA Item #A34848HA | | SPEEDO DRIVEN GEAR 43T-GM image #848J Item #A34848J | | SPEEDO DRIVEN GEAR (GRAY) 44T-GM image #848K Item #A34848K | | SPEEDO DRIVEN GEAR 45T-GM image #848L Item #A34848L | | GROMMET, Cross Shaft Linkage (GM) (White plastic half moon) image #991 Item #M463GB | | BOLT, Torque Converter Bolt M10 x 1.5 x 14.6 mm length ( Hex ) image #997 Item #M464GE | | Vacuum Regulator (CHEVY GM AC DELCO 6.2L DIESEL VACUUM VALVE GM ) image #998 Item #D34998 | |
HARD PARTS NEW | Top |
Description |
Buy |
BUSHING KIT, NO WALK CASE BUSHING, BEARING & SHIMS (SONNAX) TH400, 4L80E 4L85E image #064 Item #34006-SPB | | CARRIER OUTPUT SILENCER RING TH400 (64-UP) 4L80E (91-98) image #476 Item #34476 | | Pump Body and Gears (NEW AMD) TH400 6 Bolt holes to case 1971-ON image #510 Item #A34510 | | PUMP GEAR KIT FRONT (.727" thick) TH350 69-79: TH400 (64-UP) image #530 Item #44530AC | | HOUSING (NEW) DIRECT CLUTCH DRUM 4L80E 91-UP ( BARE DRUM WITHOUT SPRAG.) image #555 Item #A34555E | | GOVERNOR GEAR KIT 400 64-UP image #684 Item #A34684 | | PAN, TH400, 68-98, 2-DIMPLES FLAT FILTER TYPE HAS DRAIN PLUG, TOUGH POWDER COATED FINISH image #765 Item #A34765A | | PISTON 2-3 ACCUMULATOR 400 71-UP (ALUMINUM PISTON (with 3 legs) IN VALVE BODY) image #927 Item #A34927 | | Retainer, (NEW OEM) Springs Attached, (forward, direct clutch) 1991-UP image #974 Item #D34974 | |
HARD PARTS GOOD USED | Top |
Description |
Buy |
VALVE, Modulator valve TH400 64-UP img#163 Item #U34163 | | PUMP, COMPLETE (both halfs) (used) (8 BOLT) TH400 (when out can use 6 bolt pump) img#500, 510, 520 Item #U34500A | | DRUM, (used) FORWARD CLUTCH (TH400 64-98) (with input shaft) img#554, 670 Item #U34554 | | DRUM. (used) DIRECT CLUTCH HOUSING (4L80E 91-UP) (TH400 with CHECK BALL, has SPRAG TYPE RACE) img#555 Item #U34555E | | DRUM DIRECT, (used) TH400 64-UP -(WITH CHECK BALL) (WITH ONE WAY ROLLER CLUTCH TYPE LOBES) img#555 Item #U34555A | | DRUM DIRECT CLUTCH HOUSING (WITHOUT CHECK BALL) (ROLLER CLUTCH TYPE RACE) (GOOD USED) img#555 Item #U34555B | | DRUM DIRECT CLUTCH TH400, (NO CHECK BALL IN DRUM) (SPRAG TYPE RACE) (GOOD USED) img#555 Item #U34555 | | INTERMEDIATE PISTON KIT (TH400 64-UP) (USED) (INCLUDES: ALUMINUM PISTON, 3 SPRINGS, RETAINER and SNAP RING) img#562, 874, 982, 972, 962 Item #U34562K | | HUB, (used) FORWARD CLUTCH HUB TH400 67-UP img#574 Item #U34574A | | HUB, DIRECT CLUTCH / PRESSURE PLATE FORWARD CLUTCH: TH400 69-UP img#575 Item #U34575 | | CARRIER REACTION (USED) FRONT PLANET 4 GEAR HELICAL CUT TH400 (ALL) img#582 Item #U34582A | | PLANET CARRIER, FRONT (used) REACTION PLANET (4 GEAR HELICAL CUT, .795 img#582 Item #U34582B | | Rear Planet Carrier TH400 (GOOD USED) (Angled Teeth, 1.5" Parking Lugs) Add a $40.00 core charge to this part img#584 Item #U34584A | | Rear Planet Carrier TH400 (GOOD USED) (Angled Teeth, 0.5" Parking Lugs) USES THIN SNAP RING #894 .070" THICK Add a $40.00 core charge to this part img#584 Item #U34584 | | RING GEAR (REAR) (GOOD USED) HELICAL CUT GEAR: (USE WITH HOLLOW SHAFT) (TH400 64-UP) (4L80E 91-96) img#594 Item #U34594 | | RING GEAR STRAIGHT CUT (REAR) 91-96 (GOOD USED) USE WITH HOLLOW SHAFT (TH400 64-UP) (4L80E 91-96) img#594 Item #U34594S | | SUN GEAR STRAIGHT CUT: TH400 (GOOD USED) img#612 Item #U34612S | | SUN GEAR (GOOD USED) ( 32 SPLINES ) HELICAL CUT: (TH400 67-UP) (4L80E 91-96 USE WITH HOLLOW MAIN SHAFT) img#612 Item #U34612A | | SUN GEAR (GOOD USED) ( 28 SPLINES has TWO 5/16 wide SPLINES ) HELICAL CUT: (EARLY TH400 1964-67) img#612 Item #U34612 | | CENTER SUPPORT TH400 66-UP (USED) (LATE STYLE, ON EARLY UNITS INSTALL WITH CASE SNAP RING #883) img#630 Item #U34630A | | RACE ITERMEDIATE SPRAG 400 64-98 (USED) img#663 Item #U34663 | | Input Shaft (used) (65-98) TH400 img#670 Item #U34670 | | Main Shaft, (10.250" Long) (GOOD USED) ( Hollow ) TH400 (68-UP LATE SPLINE) img#672 Item #U34672 | | SHAFT SUN GEAR: (used) TH400 (1967-UP) (32 SPLINE) img#674 Item #U34674A | | SHAFT SUN GEAR (Used) TH400 (1964-66) (28 SPLINE with TWO 5/16 WIDE SLOTS) img#674 Item #U34674 | | OUTPUT SHAFT, 9" (TH400) (threaded bolt on yoke type) (USED) img#678 Item #U34678E | | Output Shaft, 15" Car (USED) (TH375 Trans) (65-??) img#678 Item #U34678A | | GOVERNOR ASSEMBLY (used with new gear) TH400 img#680 Item #U34680 | | COVER, (used) Governor cover TH400 64-UP img#686 Item #U34686 | | RETAINER, (used) TH400 TH475: Intermediate sprag or roller clutch race retainer img#694 Item #U34694 | | VALVE BODY (Used) 70-UP (With castle top accumulator piston) (Does not use smog switch. Has threaded hole for filter bolt.) img#740 Item #U34740B | | VALVE BODY (Used) 68-72 (With flat top accumulator piston) (Does not use smog switch. Has threaded hole for filter bolt.) img#740 Item #U34740A | | Extension Housing, (USED) 4" inch (Uses 34074 Rear Seal) (FITS YOKE with 1.950" OUTSIDE DIAMETER ) img#770 Item #U34770C | | Extension Housing, (USED) 4" inch (Uses 36074 Rear Seal, small ID bushing size) 65-70 (FITS YOKE with 1.750" OUTSIDE DIAMETER ) img#770 Item #U34770A | | SPEEDO HOUSING (USED) (TH400) (fits 40-45 tooth gear) img#774 Item #U34774B | | SPEEDO HOUSING (USED) (TH400) (fits 36-39 tooth gear) img#774 Item #U34774A | | BOLT, (good used) CENTER SUPPORT TH400 64-UP img#783 Item #U34783 | | BRACKET, (used) SPEEDO HOUSING HOLD DOWN (.275" BOLT HOLE) (LARGE DIAMETER SPEEDO HOUSING) TH400, TH350, TH700R4 4L60E img#842 Item #U74842 | | BRACKET, (used) SPEEDO HOUSING HOLD DOWN (.340" BOLT HOLE) (LARGE DIAMETER SPEEDO HOUSING) TH400, TH350, ST300 img#842 Item #U34842 | | Bracket Modulator hold down (Used) img#843 Item #U34843 | | SPEEDO CLIP 400 67-UP (good used) (short shaft type) img#849 Item #U34849 | | SPEEDO CLIP, (used) 400 67-UP (good used) (medium and long shaft type) img#849 Item #U34849A | | Servo assembly Intermediate (used) TH400 Late style with steel servo piston img#905, 906, 907,195, 908, 909 Item #U34905 | | REAR SERVO ASSEMBLY: TH400 (USED) (INCLUDES:946, 947, 913, 911, 912, 914, 487) img#910, 911, 912, 913, 914, 947, 946, 487 Item #U34910 | | PISTON, FORWARD / DIRECT CLUTCH (Aluminum / No check ball) 64-UP img#964, 965 Item #U34964 | | PISTON, DIRECT CLUTCH (Aluminum / WITH check ball) 64-UP img#965, Item #U34965 | | SPRING, (used) Intermediate piston return spring (each) (TH400 64-UP) img#972, 562 Item #U34972 | | RETURN SPRING, (used) DIRECT / FORWARD Piston return spring (each) TH400 64-UP img#975, 974 Item #U34975 | | RETAINER, (used) Intermediate spring retainer (FLAT PLATE) (TH400) img#982, 562 Item #U34982A | | RETAINER, (used) Intermediate spring retainer (CUPPED OUTER EDGE) (TH400) img#982, 562 Item #U34982 | | RETAINER KIT, (used) Forward / Direct clutch (Includes: piston spring retainer, 16 Springs and snap ring) TH400 64-UP img#984, 985, 975, 974, 877, 879 Item #U34984 | | Detent Spring and Roller (Used) TH400, 375, 475 64-UP img#991 Item #U34991-3 | | SHAFT, (used) Manual lever shaft 65-UP img#991-1 Item #U34991-1 | | PARK ROD and LEVER (used) Th400 img#994 Item #U34994 | |
PERFORMANCE KOLENE STEEL PLATES | Top |
Description |
Buy |
STEEL INTERMEDIATE KOLENE 4L80E .076" THICK 91-UP img#124 Item #34124EK | | STEEL INTERMEDIATE KOLENE .100" (TH400 65-98) (4L80E 91-96) img#124 Item #34124K | | STEEL KIT, FORWARD KOLENE .077" TH400 4L80E, TH425, 1965-UP (5 PER PACK) img#126, 128 Item #31703KUP5 | | STEEL KIT, DIRECT KOLENE (.090") STEEL MODULE 5 PACK. img#126, 128 Item #31711KUP5 | | STEEL KOLENE FORWARD / DIRECT .090" :TH400 4L80E 69-UP img#126, 128 Item #34126AK | | STEEL KOLENE FORWARD / DIRECT .077" :TH400 4L80E 69-UP img#126, 128 Item #34128K | | Steel Plate: Forward, Direct; .060" Kolene TH400 4L80E 1964-UP img#126, 128 Item #34126BK | | KOLENE STEEL MODULE TH400 >>more img#139, 126, 124 Item #34139HP | |
SEALING RINGS & RING KITS | Top |
Description |
Buy |
SEALING RING KIT. KIT 400 65-UP METAL CENTER SUPPORT and PUMP RINGS img#175, 181, 192, 195, 199, 198 Item #34175A | | SEALING RING KIT TH400 65-UP (ALL TEFLON RINGS) img#175, 181, 2-192, 199, 198 Item #34175AT | | SEALING RING (METAL) PUMP STATOR / CENTER SUPPORT 400 64-UP img#181 Item #34181 | | Sealing Ring, Center Support Ring (each) (Vespel Plastic) (4L80E 91-Up) (TH400 64-UP) (ON TH400 FITS PUMP STATOR ALSO) img#181 Item #34179 | |
SNAP RINGS | Top |
Description |
Buy |
Snap Ring,(USED) Holds Center Support In Case (Tapered Snap Ring) (TH400 64-UP) (4L80E 91-Up) img#872 Item #U34872 | | Snap Ring, (USED) Holds Intermediate Pressure Plate In .092" Thick (TH400 1964-UP) (4L80E, 4L85E, 91-Up) img#873 Item #U34873 | | Snap Ring, (NEW) (WIDE 727 SNAP RING) Holds Intermediate Pressure Plate In .104" Thick (91-Up) img#873 Item #A22878C | | SNAP RING, (used) intermediate spring retainer snap ring (TH400 64-UP) ( 4L80E 91-UP) img#874, 562 Item #U34874 | | SNAP RING, (used) FWD / Direct spring retainer snap ring (TH400 64-UP) (4L80E 91-UP) img#877, 879 Item #U34877 | | Snap Ring, (USED) Holds Forward and Direct Pressure Plate In drum TH400(64-Up) 4L80E(91-Up) img#878 Item #U34878 | | Spacer Snap Ring, (New) Center Support to Case, Spacer .043" THICK (TH400) (4L80E 91-Up) img#883 Item #D34883 | | Snap Ring, (USED) Center Support to Case, Spacer (TH400) (4L80E 91-Up) img#883 Item #U34883 | | Snap Ring, (NEW OEM DELCO) Holds Intermediate Sprag Retainer to Drum (91-Up) (coil type snap ring) img#886 Item #D34886E | | Snap Ring, (USED) Holds Intermediate Sprag Retainer to Drum (64-up) img#886 Item #U34886 | | SNAP RING, (used) Main shaft to rear ring gear hub img#889 Item #U34889 | | SNAP RING, (used) OUTPUT SHAFT TO PLANET .070" FLAT img#894 Item #U34894 | |
STEEL PLATES | Top |
Description |
Buy |
STEEL INTERMEDIATE FLAT 4L80E .076" THICK 91-UP img#124 Item #34124E | | STEEL INTERMEDIATE .100" (400 64-UP) (TH425) img#124 Item #34124 | | STEEL INTERMEDIATE WAVED PLATE .068 TH400 ALL YEARS, 4L80E 1991-96 img#125, 127 Item #34125 | | STEEL FORWARD FLAT .077" (TH425 TH400 65-UP) (SOME 4L80E, 4L85E ) img#126, 128 Item #34128 | | STEEL DIRECT .090" TH400 65-UP (DIRECT / FORWARD 4L80 91-UP) TH425 img#126, 128 Item #34126A | | CUSHION, FORWARD / DIRECT DISHED CUSHION - .054" (400 89-91) (4L80E 91-96) img#127 Item #34127D | | STEEL FORWARD / DIRECT WAVED ( 12 Lugs .060") TH400 65-UP img#127 Item #34127 | | STEEL MODULE, 65-89 TH400, 66-78 TH425 (with Wave plates) >>more img#139 Item #34139 | | STEEL MODULE 65-89 TH400, 66-78 TH425 (without Wave plates) >>more img#139, 126, 124 Item #S3400D | |
KOLENE STEEL PLATES | Top |
Description |
Buy |
STEEL INTERMEDIATE KOLENE 4L80E .076" THICK 91-UP img#124 Item #34124EK | | STEEL INTERMEDIATE KOLENE .100" (TH400 65-98) (4L80E 91-96) img#124 Item #34124K | | STEEL KIT, FORWARD KOLENE .077" TH400 4L80E, TH425, 1965-UP (5 PER PACK) img#126, 128 Item #31703KUP5 | | STEEL KIT, DIRECT KOLENE (.090") STEEL MODULE 5 PACK. img#126, 128 Item #31711KUP5 | | STEEL KOLENE FORWARD / DIRECT .090" :TH400 4L80E 69-UP img#126, 128 Item #34126AK | | STEEL KOLENE FORWARD / DIRECT .077" :TH400 4L80E 69-UP img#126, 128 Item #34128K | | Steel Plate: Forward, Direct; .060" Kolene TH400 4L80E 1964-UP img#126, 128 Item #34126BK | | KOLENE STEEL MODULE TH400 >>more img#139, 126, 124 Item #34139HP | |
TORQUE CONVERTERS reman | Top |
Description |
Buy |
Torque Converter select returned 4 rows.
| TC 13" DIAMETER, V8 HEAVY DUTY, 3 PADS, LARGE BEARING, 13K-15K STALL FOR R.V. and TRUCK APPLICATION, GAS and DIESEL, BRAZED FINS Add an addition refundable core charge of $45.00 Item #A3HD | | 13" DIAMETER, V8 HEAVY DUTY, LARGE BEARING, 6 PADS, 13K-15K STALL FOR R.V. and TRUCK APPLICATION, GAS and DIESEL BRAZED FINS BU6FM Add an addition refundable core charge of $55.00 Item #A6HD | | TC 13" DIAMETER, V8 PASSENGER CARS, 13K - 15K STALL, 11.5" Bolt Circle 3 Rows of Ribs, Fixed Pitch Stator, (NOT FOR TRUCKS) Add an addition refundable core charge of $75.00 Item #GM3 | | 13 DIAMETER, 1500-1700 STALL, 11.5" BOLT CIRCLE, 6 Bolt Pads V8 Engines, light & Medium Duty trucks Item #GM6 | |
WASHERS & BEARINGS | Top |
Description |
Buy |
WASHER KIT: WithOut PUMP SELECTIVES TH400, 4L80E more info>> img#200 Item #K34940 | | BEARING KIT 3 TORRINGTONS 400 64-98 (4L80E 91-up DOES NOT INCLUDE #217 Overdrive planet to forward drum bearing img#200, 242, 249, 256 Item #34201A | | WASHER FRONT PUMP SELECTIVE .062" 400 64-UP img#211 Item #34211 | | WASHER FRONT PUMP SELECTIVE .073" 400 64-UP img#211 Item #34211A | | WASHER FRONT PUMP SELECTIVE .084" 400 64-UP img#211 Item #34211B | | WASHER FRONT PUMP SELECTIVE .095" 400 64-UP img#211 Item #34211C | | WASHER FRONT PUMP SELECTIVE .106" 400 64-UP img#211 Item #34211D | | WASHER FRONT PUMP SELECTIVE .117" 400 64-UP img#211 Item #34211E | | WASHER FRONT PUMP SELECTIVE .128" 400 64-UP img#211 Item #34211G | | WASHER CENTER SUPPORT to PLANET (BRONZE) img#226 Item #34226 | | WASHER FORWARD HUB to FORWARD DRUM (FRONT) 400/4L80E img#232 Item #34232 | | WASHER FORWARD HUB (FRONT) to FORWARD DRUM OVERSIZED .078" Thick (SONNAX) each img#232 Item #34298-078 | | WASHER FORWARD HUB to DIRECT DRUM .062" 400/4L80E img#235 Item #34235 | | WASHER FORWARD HUB to DIRECT DRUM .078" 400 / 4L80 (1 EACH) (SONNAX) img#235 Item #S34235-078 | | WASHER FORWARD HUB to DIRECT DRUM .094" 400 / 4L80 (1 EACH) (SONNAX) img#235 Item #S34235-94 | | BEARING CENTER SUPPORT to SUN GEAR TH400,4L80E (When out buy bearing kit 34201A TH400 OR 4L80E 34200E) img#242 Item #34920 | | WASHER (4L80E, TH400 PLANET to PLANET 4 TANG PLASTIC ) (SHELL to CENTER SUPPORT .060" TH200 / 2004R / 325 / 325-4L) img#244, 268 Item #54244A | | BEARING REAR RING GEAR to SUN GEAR TH400, 4L80E (When out buy bearing kit 34201A TH400 OR 4L80E 34200E) img#249 Item #34921 | | SHIM KIT: UNDER RACE #256 to REAR RING GEAR .010" TH400, 4L80E (REDUCE END PLAY IN GEAR TRAIN) (3 PER KIT) img#252 Item #34252S-3 | | BEARING REAR RING GEAR to OUTPUT SHAFT TH400 4L80E (When out buy bearing kit 34201A TH400 OR 4L80E 34200E) img#256 Item #34922 | | WASHER OUTPUT and PLANET to PLANET 4 TANG (METAL) TH400 / 4L80E img#268 Item #34268 | | WASHER, (AMD) FRONT PLANET to REAR PLANET (2 TANG, PLASTIC) img#268 Item #A34268A | | WASHER OUTPUT SHAFT CASE SELECTIVE 3 TAB .074-.078 400/4L80 img#269 Item #34269 | | WASHER OUTPUT SHAFT CASE SELECTIVE 3 TAB .082-.086 400/4L80 img#269 Item #34269A | | WASHER OUTPUT SHAFT CASE SELECTIVE 3 TAB .090-.094 400/4L80 img#269 Item #34269B | | WASHER OUTPUT SHAFT CASE SELECTIVE 3 TAB .098-.102 400/4L80 img#269 Item #34269C | | WASHER OUTPUT SHAFT CASE SELECTIVE 3 TAB .114-.118 400/4L80 img#269 Item #34269E | | WASHER OUTPUT SHAFT CASE SELECTIVE 3 TAB .106-.110 400/4L80 img#269 Item #34269D | |
|